Recently Completed Jobs by Politon

November 12, 2021 | Fort Worth, TX

Baumann asked us to install two Quad data outlets for future use on some new cubicle workstations. We pulled the cable out the opening with about twenty feet of slack and a four-square box with a faceplate on it. We also installed a dual data run in the same room ...

September 30, 2021 | Plano, TX

We provided technical support to install the customer's hardware solutions for Wifi, network switches and routers, network cabinets, and UPS with extended batteries. This was a fairly small office so the network cabling for the wifi was very easy. We installed four wifi access points for the customer. They had ...

September 28, 2021 | Dallas, TX

The solution we provided was a two-strand single-mode fiber from their dmarc room to their network cabinet in the MDF closet. We installed LC connectors on both ends and certified the connection with our Owl Fiber Tester. The customer asked us after the fiber installation if we could assist him ...

September 10, 2021 | Frisco, TX

Our new customer in Frisco wanted us to install a four-post data rack they already had into their new data closet on the 4th floor. We installed approximately 64 Cat 6 data cables along with seven Cat 6A cables. The customer requested Cat 6A for all of their Wifi access points. They ...

September 10, 2021 | Denton, TX

We have worked several tickets very similar to this one for our customer. They have Invisalign fiber installed on the surface of their walls. This was a fiber retrofit method after the apartments had been built. It's a great product for this solution but the downside is if you run ...

August 31, 2021 | Denton, TX

To get to a resolution on this trouble ticket we worked for them was a multi-step process. First, we had to do a port audit which involved patching in a laptop doing a continuous ping into every network switch port in each of ten network closets across the property. This ...

August 27, 2021 | Carrollton, TX

We ended up repairing the LC connectors on six strands of the single-mode fiber. Luckily the cable was lowered to the ground which allowed easy access to the cable the challenging part was there was very little slack to work with. To reinforce the fibers we had to use heat ...

August 27, 2021 | McKinney, TX

We ended up installing all the data cabling, data rack, network switch, Wifi access point, and NVR. We helped the doctor get her office up and running. The customer provided their own security cameras and NVR but we installed the cameras and the cabling back to the NVR. There were ...

August 6, 2021 | Fort Worth, TX

We installed a SIP gateway paging solution that allowed their Ring Central phones to be able to page out to a traditional analog paging system. The customer wanted us to move one existing 5-watt Valcom paging horn and to add one new horn. We provided a Valcom VRCPA (Valcom Ring ...

August 5, 2021 | North Richland Hills, TX

The customer had has come out again to pull a new fiber between these two buildings into the new conduit that was installed much deeper underground. The school has also marked the path of this new conduit and fiber for future reference. The problem in the past is they did ...

August 3, 2021 | Dallas, TX

Our contact wanted to update their network cabling to all Cat 6 from what they currently have which is Categroy 5. They also wanted us to clean up their data rack and install wire management.

July 19, 2021 | Fort Worth, TX

There were several solutions we installed here in addition to the new Cat 6 data cabling. We installed wall mount brackets with Cat 6 HDMI extensions from their NVR to allow two employees to view the security cameras from their offices. We provided two sets of HDMI extenders by Calrad. The customer ...

July 14, 2021 | Haslet, TX

We ended up installing (13) Wifi Access Points at this Haslet location as well as (40) Cat 6 data cables to pack outstations. We used 24" X 24" 1/2" plywood for the backboards and painted them fluorescent orange per the customers' request for the pendant-mounted access points. The customer let us install their new Cisco POE ...

July 9, 2021 | McKinney, TX

The best solution for this customer was a 6 strand multi-mode armored fiber between the first floor and the fourth floor to join two businesses that recently merged. The armored wrap protects the fiber without having to install costly innerduct which is more expensive and a less efficient installation. The fiber ...

July 8, 2021 | Corinth, TX

This customer wanted a low-cost solution so they opted out of using patch panel and just wanted us to put male RJ-45 ends on the cable and plug them directly into their switch. At the end-user side, the builder used dual-gang boxes so we had to find a dual gang ...